earwicker7
In Runtime
- Messages
- 345
I'm working on my overclock, and was able to get my BCLK to 145 and do a 20 minute run of LixX with a couple of voltage adjustments, so I went to the next step and raised the BCLK to 150. LinX immediately gave me the following message: "linpack_xeon64.exe has stopped working". I was hoping someone might give me an idea of which voltage needs to be bumped to avoid this message.
I'm going to use Slaymates questionairre to give the details.
Bios Template
•Mother Board (Gigabyte GA-X58A-UD9)
•Drivers (all current)
•Bios (5fg )
•CPU (i7-980X)
•CPU Cooler (stock)
•Memory ( G.Skill Trident+ Turbulence II 12GB (3 x 4GB) DDR3 2000)
•PSU (Silverstone ST1500 1500W)
•GPU (2 x XFX ATI Radeon HD 5970 2 GB)
•Drivers (Catalyst 10.11--drivers only)
•Operating System (Windows 7 64-bit)
Frequency Control
•CPU Clock Ratio (25X)
•CPU Host Frequency/BCLK (150)
•MCH Strap (???)
•CPU Uncore Frequency (3000 MHz {X20})
•CPU Clock Skew (0 ps)
•Spread Spectrum (???)
•PCIE Frequency (Auto)
•OC Recovery (???)
Here are some Frequency settings that weren't mentioned, as I couldn't find all of the ones requested:
QPI Clock Ratio (Auto)
QPI Link Speed (5.4 GHz)
Extreme Memory Profile (Disabled)
PCI Express Clock Drive (900 mV)
CPU Clock Drive (800mV)
IOH Clock Skew (0 ps)
Memory Feature
•Memory Speed (10X)
•Memory Control Setting (???)
•Memory Frequency (1500)
•Channel Interleave Setting (Auto)
•Rank Interleave Setting (Auto)
•Memory Low Gap (???)
•tCL Setting (10)
•tRCD Setting (10--Auto)
•tRP Setting (10--Auto)
•tRAS Setting (28--Auto)
•tRFC Setting (122--Auto)
•Command Rate (1--Auto)
Some Memory settings that weren't mentioned:
Performance Enhance (Standard)
DRAM Timing Selectable (Auto)
Voltage Control
•EVGA VDroop Control/Load Line Calibration (standard)
•CPU VCore (1.26250V--stock is 1.25625)
•CPU VTT/QPI DRAM Voltage (1.175V)
•CPU PLL VCore (1.800V)
•DIMM Voltage (1.500V)
•DIMM DQ Vref (???)
•QPI PLL VCore (1.140V--stock is 1.100 )
•IOH VCore (1.100V)
•IOH/ICH I/O Voltage (1.500V)
•ICH VCore (1.100V )
•PWM Frequency (???)
There was one Voltage setting that wasn't mentioned:
PCIE (1.500V)
CPU Feature
•Intel SpeedStep (Disabled)
•Turbo Mode Function (Auto)
•CxE Function (???)
•Execute Disable Bit (Enabled)
•Virtualization Technology (Disabled)
•Intel HT Technology (Enabled)
•Active Processor Cores (All)
•QPI Control Settings (???)
•QPI Link Fast Mode (???)
•QPI Frequency Selection (???)
Here are some that weren't mentioned:
QPI Clock Ratio (Auto)
QPI Link Speed (5.4 GHz)
CPU Enhanced Halt--Disabled
C3/C5/C7 State Support--Disabled
CPU Thermal Monitor--Enabled
Bi-Directional PROCHOT--Enabled
I'm going to use Slaymates questionairre to give the details.
Bios Template
•Mother Board (Gigabyte GA-X58A-UD9)
•Drivers (all current)
•Bios (5fg )
•CPU (i7-980X)
•CPU Cooler (stock)
•Memory ( G.Skill Trident+ Turbulence II 12GB (3 x 4GB) DDR3 2000)
•PSU (Silverstone ST1500 1500W)
•GPU (2 x XFX ATI Radeon HD 5970 2 GB)
•Drivers (Catalyst 10.11--drivers only)
•Operating System (Windows 7 64-bit)
Frequency Control
•CPU Clock Ratio (25X)
•CPU Host Frequency/BCLK (150)
•MCH Strap (???)
•CPU Uncore Frequency (3000 MHz {X20})
•CPU Clock Skew (0 ps)
•Spread Spectrum (???)
•PCIE Frequency (Auto)
•OC Recovery (???)
Here are some Frequency settings that weren't mentioned, as I couldn't find all of the ones requested:
QPI Clock Ratio (Auto)
QPI Link Speed (5.4 GHz)
Extreme Memory Profile (Disabled)
PCI Express Clock Drive (900 mV)
CPU Clock Drive (800mV)
IOH Clock Skew (0 ps)
Memory Feature
•Memory Speed (10X)
•Memory Control Setting (???)
•Memory Frequency (1500)
•Channel Interleave Setting (Auto)
•Rank Interleave Setting (Auto)
•Memory Low Gap (???)
•tCL Setting (10)
•tRCD Setting (10--Auto)
•tRP Setting (10--Auto)
•tRAS Setting (28--Auto)
•tRFC Setting (122--Auto)
•Command Rate (1--Auto)
Some Memory settings that weren't mentioned:
Performance Enhance (Standard)
DRAM Timing Selectable (Auto)
Voltage Control
•EVGA VDroop Control/Load Line Calibration (standard)
•CPU VCore (1.26250V--stock is 1.25625)
•CPU VTT/QPI DRAM Voltage (1.175V)
•CPU PLL VCore (1.800V)
•DIMM Voltage (1.500V)
•DIMM DQ Vref (???)
•QPI PLL VCore (1.140V--stock is 1.100 )
•IOH VCore (1.100V)
•IOH/ICH I/O Voltage (1.500V)
•ICH VCore (1.100V )
•PWM Frequency (???)
There was one Voltage setting that wasn't mentioned:
PCIE (1.500V)
CPU Feature
•Intel SpeedStep (Disabled)
•Turbo Mode Function (Auto)
•CxE Function (???)
•Execute Disable Bit (Enabled)
•Virtualization Technology (Disabled)
•Intel HT Technology (Enabled)
•Active Processor Cores (All)
•QPI Control Settings (???)
•QPI Link Fast Mode (???)
•QPI Frequency Selection (???)
Here are some that weren't mentioned:
QPI Clock Ratio (Auto)
QPI Link Speed (5.4 GHz)
CPU Enhanced Halt--Disabled
C3/C5/C7 State Support--Disabled
CPU Thermal Monitor--Enabled
Bi-Directional PROCHOT--Enabled