I recently made the huge mistake of buying a Cyberpower Computer with an Xtremegear 600W Power Supply. (2 mistakes actually)
I guess I read one too few threads before choosing the components for this build.
After 2 months, my monitor has begun to dim and my Aerocool 2000 Fan Control, Temp Sensor unit is considerably dimmer than 2 months ago.
I followed the advise of just about everybody and ordered a Corsair 750TX PSU.
I already knew I was going to find quite a wiring bundle on the new PSU, by reading and looking at the Newegg photos. What I didn't expect was what I found when I opened the wiring side of the Coolermaster HAF 912 case.
I guess this should not have been a big surprise to me as the build has a DVD Drive, Card Reader & the Aerocool unit taking up 4 bays in the front of the unit. Between the fan control wires, the temp sensors and the power cables, you wouldn't believe what it looks like.
I took a deep breath and said "I just need to follow the wires from the power supply and label them as I disconnect them. I quickly found out that this was going to be a task and a half.
The peripheral cables on the existing power supply were plugged into other peripheral cables, which then branched off to either a component or split to two two wire plugs, which I can't even see where they are going.
Even the Geforce GTX 460 GPU is confusing. The old power supply has two 6 hole plugs, but one of the plugs is a dummy, so there are only 5 wires per plug. The Corsair has the two 6 plug holes, with 6 wires in each.
I still didn't want to give up, so I said maybe I can just disconnect at the very first connection for each bundle coming out of the old PSU and just connect the new PSU to those points, forgetting about where all these other branch offs go to. I quickly noticed that each individual wire coming out of the Corsair was almost twice as thick as those coming out of the XtremeGear. To me, I think the only way to do this properly would be to go from the PSU to the component, not using all these thin wired connections and branch offs.
Even the AC cord to the Corsair is considerably heavier than the XtremeGear.
If I didn't already take a beating from Cyberpower, I might just take it somewhere and pay to have it installed.
Cyberpower refused to do anything but send me another XtremeGear PSU, even though they must be aware of the poor quality, especially if they read their own forums. They wouldn't even allow me to pay them the upgrade for the Corsair. Even if they sent me the same XtremeGear unit, which would make no sense, they wouldn't do that until I returned their $25.00 POS first.
My head is spinning over this and I am afraid that if I don't get this Corsair in there, my components will be degrading by the minute.
I understand that without seeing the unit, it is very difficult to make suggestions, but I really need some help on this one.
Thanks All!!!!
I guess I read one too few threads before choosing the components for this build.
After 2 months, my monitor has begun to dim and my Aerocool 2000 Fan Control, Temp Sensor unit is considerably dimmer than 2 months ago.
I followed the advise of just about everybody and ordered a Corsair 750TX PSU.
I already knew I was going to find quite a wiring bundle on the new PSU, by reading and looking at the Newegg photos. What I didn't expect was what I found when I opened the wiring side of the Coolermaster HAF 912 case.
I guess this should not have been a big surprise to me as the build has a DVD Drive, Card Reader & the Aerocool unit taking up 4 bays in the front of the unit. Between the fan control wires, the temp sensors and the power cables, you wouldn't believe what it looks like.
I took a deep breath and said "I just need to follow the wires from the power supply and label them as I disconnect them. I quickly found out that this was going to be a task and a half.
The peripheral cables on the existing power supply were plugged into other peripheral cables, which then branched off to either a component or split to two two wire plugs, which I can't even see where they are going.
Even the Geforce GTX 460 GPU is confusing. The old power supply has two 6 hole plugs, but one of the plugs is a dummy, so there are only 5 wires per plug. The Corsair has the two 6 plug holes, with 6 wires in each.
I still didn't want to give up, so I said maybe I can just disconnect at the very first connection for each bundle coming out of the old PSU and just connect the new PSU to those points, forgetting about where all these other branch offs go to. I quickly noticed that each individual wire coming out of the Corsair was almost twice as thick as those coming out of the XtremeGear. To me, I think the only way to do this properly would be to go from the PSU to the component, not using all these thin wired connections and branch offs.
Even the AC cord to the Corsair is considerably heavier than the XtremeGear.
If I didn't already take a beating from Cyberpower, I might just take it somewhere and pay to have it installed.
Cyberpower refused to do anything but send me another XtremeGear PSU, even though they must be aware of the poor quality, especially if they read their own forums. They wouldn't even allow me to pay them the upgrade for the Corsair. Even if they sent me the same XtremeGear unit, which would make no sense, they wouldn't do that until I returned their $25.00 POS first.
My head is spinning over this and I am afraid that if I don't get this Corsair in there, my components will be degrading by the minute.
I understand that without seeing the unit, it is very difficult to make suggestions, but I really need some help on this one.
Thanks All!!!!