Recent content by typicol

Would that be something obvious(blow out my rails), I only did it once at the end to test out every thing I could think of. I have a new z77 mobo that should be in Tuesday if mine has gone bad somehow

So, correct me if I am wrong, if my fans on my video card both 560 ti and 660 ti ftw, are running without power from cables, just inserted in the pcie 3.0. Then that slot is working correctly right, because if it wasn't there would be no power distribution to the card, so if that is the case...

600 w corsair The thing is I've been reading a lot of forums about people having a similar experience as me 3rd gen i3 trying to install into a pcie 3.0 and it not being detected, or running in 2.0 still PCI-e 3.0 GPU + MoBo + Ivy CPU = PCI-e 2.0 ??? - Graphics Cards - Graphics & Displays GTX...

So how after I pull out my 660 to try it out, my 560 no longer works in the same slot it's been in for almost a year, but it does work in my 2.0 slot?

I3 3220 CPU 16 gb ram 560 ti gpu Asrock h77 MVP/pro3 So Lets just say my 660 ftw didn't work after installing drivers, I remove it from my pcie 3.0 slot and put my old 560 in to see what I could do, now that one isn't being detected, but both cards have their fans running so they're are...

So after about a month after my initial plan to build my own computer. I think i finally have what it a damn good computer setup for under 1k My specs: 560 GTX Ti - 180 3.3 Ivy Bridge CPU - 70 Asrock H77 MVP Mobo- 70 Corsair 600CX PSU - 40 16 GB Corsair Vengeance Ram 70 1TB Seagate HDD 7200...

nm i think i got i

Well new HDD and everything is good, now I think I'm at my last question. Its saying that I need an Ethernet Controller Driver, can i DL that online cause ive been looking with no luck.

I dont have another to try it, If I go buy a brand new HDD 500gb 6Gbs should that solve it, cause it really feels like my HDD arent doing ****, I did drop one very bad on concrete the day I was building this, and it is making a very sprangy noise, like a forking fork almost, but the other has...

still nothing, have em both into the gray SATA ports, and on my bio still shows nothing is being detected, When i boot up now i get Asmeia 106X SATA controller Ver 0.93 AHCI Mode Copyright SMART supported Using PCIE Gen 2 usually it say device cannot be find, and its doing it again now, but...

XX0 the two XX of the six on the bottom are where the sata cables are connected, 000 and yes i have it on AHCI, atleast that is what the manual recommended. ive tried these cables in every SATA location is vary cables, and it is always the same, though I want to say I remember well looking at...

I'm not sure on what RAID is, it is just running 2 different HDDs so you dont have a 640 gb but 2 320gb, I'm not sure, ive been in bios and tried setting under raid and nothing changed. i can feel my HHD being powered but not connecting to mobo. atm im just trying 1 HDD, still nothing.

ok so figured out the PS issue, but back at the same spot where it says it cant detect any drivers, I have 3 SATA cables connected yet only the one attach to my CD/DVD ROM, I have 2 320gb HDD connected to the mobo but they arent being detected, is being detected on the mother board according to...

Exactly

So after putting this together, btw im using my old hp media center 8020n so everything is stock outside of what I bought. after 1st putting everything in and connected it started up fine, and working with windows 7, had some trouble, finally got to the install windows 7, and then when I get...