kernel_data_inpage_error - Techist - Tech Forum

Go Back   Techist - Tech Forum > Computer Software > Microsoft Windows and Software
Closed Thread
Thread Tools Display Modes
Old 05-11-2005, 04:28 PM   #1 (permalink)
True Techie
Join Date: Dec 2003
Posts: 139
Default kernel_data_inpage_error

On a computer I just built using all new parts (and one old hdd), I keep getting the "kernel_data_inpage_error" screen. I Googled it and someone said that it means the hdd on which XP is installed is set to slave; someone else said it means the hdd is giving out. Would setting the hdd to master solve the problem? I'm guessing it's not the latter because it's a brand new computer.

-The one and only Keebler Elf-
Squaggleboggin is offline  
Old 05-11-2005, 04:31 PM   #2 (permalink)
Field Engineer
SHAWN's Avatar
Join Date: Nov 2004
Location: Long Island, NY
Posts: 4,697
Send a message via AIM to SHAWN

Did you check the jumpers on it and set it to master an see if it solved the problem before you posted this?

A+, Network + , HP Certified Tech and MCP

Specs: AMD Phenom II X6 1095T, Asus M477TD, 8GB GSkill Ripjaws DDR3 1600 7-8-7-24 1T, 128GB Crucial M4 SSD, ATi HD4650, W7, 27" HL272 Monitor
SHAWN is offline  
Old 05-11-2005, 04:49 PM   #3 (permalink)
Techie Beyond Description
Osiris's Avatar
Join Date: Jan 2005
Location: Kentucky
Posts: 36,817
Send a message via ICQ to Osiris Send a message via AIM to Osiris Send a message via MSN to Osiris Send a message via Yahoo to Osiris

I need to know what the second parameter is....which is usually ox00000007A as an example.

Here are some possible causes:

0xC000009A, or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of nonpaged pool resources.

0xC000009C, or STATUS_DEVICE_DATA_ERROR, indicates bad blocks (sectors) on the hard disk.

0xC000009D, or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose data or power cables, a problem with SCSI termination, or improper controller or disk configuration.

0xC000016A, or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk.

0xC0000185, or STATUS_IO_DEVICE_ERROR, indicates improper termination, defective storage controller hardware, or defective disk cabling, or two devices attempting to use the same resources.

Resolving the Problem

Stop 0x7A can be caused by bad sectors in the virtual memory paging file, disk controller error, virus infection, or memory hardware problems. In extremely rare cases, depleted nonpaged pool resources can cause this error. If the first and third parameters are zero, the stack signature in the kernel stack is missing, an error typically caused by defective hardware. If the I/O status is 0xC0000185 and the paging file is on a SCSI disk, check for cabling and termination issues. An I/O status code of 0xC000009C or 0xC000016A indicates that the requested data could not be found. You can try to correct this by restarting the computer. If a problem with disk integrity exists, Autochk, a program that attempts to mark bad disk sectors as defective so that they are not used in the future, starts automatically. If Autochk fails to run, you can manually perform the integrity check yourself by following the instructions to run Chkdsk provided in "Stop 0x00000024 or NTFS_FILE_SYSTEM" earlier in this appendix. For more information about Autochk and Chkdsk, see "Troubleshooting Disks and File Systems" in this book.

Another cause of Stop 0x7A messages is defective, malfunctioning, or failed memory hardware, such as memory modules, Level 2 (L2) SRAM cache, or video adapter RAM. If you added new hardware recently, remove and replace it to determine if it is causing or contributing to the problem. Run diagnostics software supplied by the system manufacturer to determine if the component has failed.

Check the hardware manufacturer's Web site for updates to disk adapter firmware or drivers that improve compatibility. Verify that your disks and controller support the same set of advanced features, such as higher transfer rates. If necessary, select a slower transfer rate if an update is not yet available. Consult your hardware or device documentation for more information.


You can install disk controller drivers not present on the Windows XP Professional operating system CD by responding to the following prompt shortly after starting Setup:
Press F6 if you need to install a third party SCSI or RAID driver.
Press F6, and when prompted, provide the appropriate storage controller driver (ATA or SCSI) supplied by the manufacturer.

The problem might also be due to cracks, scratched traces, or defective components on the motherboard. If all else fails, take the system motherboard to a repair facility for diagnostic testing.

Problems that cause Stop 0x7A messages can also cause Stop 0x77 messages. For more information about Stop 0x77 messages, see "Stop 0x00000077 or KERNEL_STACK_INPAGE_ERROR" earlier in this appendix.

Does this help? Did I list the correct parameter?
Osiris is offline  
Old 05-11-2005, 06:54 PM   #4 (permalink)
True Techie
Join Date: Dec 2003
Posts: 139

Thanks for the replies. I just found the CD that came with the mobo for all the drivers (smacks self on forehead). I must've been pretty excited when I first opened everything, because this is the second thing I've missed so far. I copied down what the error said last time it came up. "stop: 0x0000007A (0xE16EFD7C, 0xC000000E, 0xBF9238C6, 0x19D42860) [next line] win32k.sys - address BF9238C6 base at BE800000, datestamp 4225181e"
-The one and only Keebler Elf-
Squaggleboggin is offline  
Old 05-11-2005, 06:59 PM   #5 (permalink)
True Techie
Join Date: Dec 2003
Posts: 139

I should also say that when I set my other (newer, better) hdd to master, it doesn't detect the other hdd and won't even boot. That's why I have it set to slave in the first place. I suppose I could try again since I installed RAID drivers from the mobo disc, anyone think that would solve the problem (like I said I tried once before and it didn't work, but that was without the new drivers)?
-The one and only Keebler Elf-
Squaggleboggin is offline  
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off

Our Communities

Our communities encompass many different hobbies and interests, but each one is built on friendly, intelligent membership.

» More about our Communities

Automotive Communities

Our Automotive communities encompass many different makes and models. From U.S. domestics to European Saloons.

» More about our Automotive Communities

Marine Communities

Our Marine websites focus on Cruising and Sailing Vessels, including forums and the largest cruising Wiki project on the web today.

» More about our Marine Communities

Copyright 2002-2015 Social Knowledge, LLC All Rights Reserved.

All times are GMT -5. The time now is 04:09 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2016, vBulletin Solutions, Inc.