I have a harddrive which is almost dead, and here is the situation:
- It's an external harddrive WD 120GB HHD(I took the cover off, and I will connect it using HDD > USB cable)
- Harddrive still spins(there is a clocking sound) when it's COLD, when it warms up it stops spinning(dies).
- I can trun it on while it's "cool"(room temperature) but i can't open it(windows does not see it). HOWEVER, today when I plugged it in, waited for 90 seconds, that thing when you plugg in new
hardware appeared by the clock(right botton corner), but then the harddrive stopped(most likely warmed up again).
It's almost full 100GB/120GB, and I need all data from it.
Here is what I'm going to do and questions I have:
1. Freeze the harddrive(put it in the freezer)
- What is the best way to seal it? Zip lock back is ok? or should I seal it using something else? Like wrap it to a paper towels, and put it into couple zip lock bags? By doing that I want to make
sure that when I turn it on that there would not be any water so it would not fail permenently due a water + eletricity. Does this sound right?
- Also do you know if i can repeat(the freezing processes) many times? for example: Freeze it, copy data of it, when it dies, freeze it again and so on? or it will die after the first time it melts
down?
2. Plug it in while it's in the freezer
3. Have my fingers crossed that windows will recognize it.
- What would be the best software/way to have it recognized?
This is my first time doing it and I'v read a little bit about it but still unsure.
Any help would be appreaciated.
Edited:
Also forgot to ask:
- How long should I keep it in the Freezer(I need all data, at least the most i can get)
- I have a SLOW laptop(512MB/1.6Ghz) and FAST DESKTOP(8GB/4x2.5Ghz), which one should I use for data transfer?
- It's an external harddrive WD 120GB HHD(I took the cover off, and I will connect it using HDD > USB cable)
- Harddrive still spins(there is a clocking sound) when it's COLD, when it warms up it stops spinning(dies).
- I can trun it on while it's "cool"(room temperature) but i can't open it(windows does not see it). HOWEVER, today when I plugged it in, waited for 90 seconds, that thing when you plugg in new
hardware appeared by the clock(right botton corner), but then the harddrive stopped(most likely warmed up again).
It's almost full 100GB/120GB, and I need all data from it.
Here is what I'm going to do and questions I have:
1. Freeze the harddrive(put it in the freezer)
- What is the best way to seal it? Zip lock back is ok? or should I seal it using something else? Like wrap it to a paper towels, and put it into couple zip lock bags? By doing that I want to make
sure that when I turn it on that there would not be any water so it would not fail permenently due a water + eletricity. Does this sound right?
- Also do you know if i can repeat(the freezing processes) many times? for example: Freeze it, copy data of it, when it dies, freeze it again and so on? or it will die after the first time it melts
down?
2. Plug it in while it's in the freezer
3. Have my fingers crossed that windows will recognize it.
- What would be the best software/way to have it recognized?
This is my first time doing it and I'v read a little bit about it but still unsure.
Any help would be appreaciated.
Edited:
Also forgot to ask:
- How long should I keep it in the Freezer(I need all data, at least the most i can get)
- I have a SLOW laptop(512MB/1.6Ghz) and FAST DESKTOP(8GB/4x2.5Ghz), which one should I use for data transfer?