Case: COOLER MASTER COSMOS 1000
Mobo: GIGABYTE GA-P35-DS3L LGA 775 Intel P35 ATX
PSU: Thermaltake W0106RU Complies with ATX 12V 2.2 & EPS 12V version 700W Power Supply 100
Soundcard: Creative 70SB046A00000 7.1 Channels 24-bit 192KHz PCI Interface Sound Blaster X-Fi XtremeGamer Fatal1ty Professional Series
RAM: Patriot Extreme Performance 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory
Hard Drive 1: Western Digital Caviar SE WD5000AAJS 500GB 7200 RPM 8MB Cache SATA 3.0Gb/s Hard Drive - OEM
Hard Drive 2: Western Digital Raptor WD1500ADFD 150GB 10000 RPM 16MB Cache SATA 1.5Gb/s Hard Drive - OEM
Graphics Card: EVGA 512-P3-N801-AR GeForce 8800GT 512MB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI Supported Video Card
DVD-Ram: Newegg.com - Sony NEC Optiarc Black 20X DVD+R 8X DVD+RW 8X DVD+R DL 20X DVD-R 6X DVD-RW 16X DVD-ROM 48X CD-R 32X CD-RW 48X CD-ROM SATA 20X DVD±R DVD Burner - CD / DVD Burners
CPU: Intel Xeon E3110 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W Dual-Core Processor
Ok I have a problem. I have just built this computer and have installed all the drivers and everything worked for a good 2 weeks. Then due to one simple thing it messed up. I have this senior ex project and I needed the pictures from my old computer which is a Dell 8400. All I did was switch the RGB cable from my new computer to the old and then switch it back and then I had no signal at all from the monitor. I tested this with 2 other monitors and the same result happened. I therefore concluded that it was my hard drive so I reformatted it successfully and reinstalled the drivers again. This fixed the monitor problem but it was short lived when I returned after shutting off the computer. I turned it on and it loaded everything but when it came to the windows bar right before you log into your account I received that the WINDOWS/MS/CONFIG file was missing and therefore would not start it kept saying "press r to repair from windows xp disk. I was baffled, frustrated, and angry when it said this because I'm like "how can the configuration file just get up and leave". I then did what it asked and tried to reformatted again but worse was upon me. When I put the disk it and ran it it went through its normal motions and I got to as far as when you have to press the F8 key to accept. When I did this it went to the bluescreen of death saying I had a BAD_POOL_CALLER with the numbers 0x000000C2 (0x0000043, 0xC1EA9000, 0X00000000, 0X00000000. This is where I'm currently stuck if anyone out there can tell me how to recover my Raptor Drive to work or completely wipe everything out of it I will the the happiest person ever. Thank you.
Update*
I have currently installed my OS on my normal 500GB harddrive
raptor drive still needs help.
Mobo: GIGABYTE GA-P35-DS3L LGA 775 Intel P35 ATX
PSU: Thermaltake W0106RU Complies with ATX 12V 2.2 & EPS 12V version 700W Power Supply 100
Soundcard: Creative 70SB046A00000 7.1 Channels 24-bit 192KHz PCI Interface Sound Blaster X-Fi XtremeGamer Fatal1ty Professional Series
RAM: Patriot Extreme Performance 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory
Hard Drive 1: Western Digital Caviar SE WD5000AAJS 500GB 7200 RPM 8MB Cache SATA 3.0Gb/s Hard Drive - OEM
Hard Drive 2: Western Digital Raptor WD1500ADFD 150GB 10000 RPM 16MB Cache SATA 1.5Gb/s Hard Drive - OEM
Graphics Card: EVGA 512-P3-N801-AR GeForce 8800GT 512MB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI Supported Video Card
DVD-Ram: Newegg.com - Sony NEC Optiarc Black 20X DVD+R 8X DVD+RW 8X DVD+R DL 20X DVD-R 6X DVD-RW 16X DVD-ROM 48X CD-R 32X CD-RW 48X CD-ROM SATA 20X DVD±R DVD Burner - CD / DVD Burners
CPU: Intel Xeon E3110 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W Dual-Core Processor
Ok I have a problem. I have just built this computer and have installed all the drivers and everything worked for a good 2 weeks. Then due to one simple thing it messed up. I have this senior ex project and I needed the pictures from my old computer which is a Dell 8400. All I did was switch the RGB cable from my new computer to the old and then switch it back and then I had no signal at all from the monitor. I tested this with 2 other monitors and the same result happened. I therefore concluded that it was my hard drive so I reformatted it successfully and reinstalled the drivers again. This fixed the monitor problem but it was short lived when I returned after shutting off the computer. I turned it on and it loaded everything but when it came to the windows bar right before you log into your account I received that the WINDOWS/MS/CONFIG file was missing and therefore would not start it kept saying "press r to repair from windows xp disk. I was baffled, frustrated, and angry when it said this because I'm like "how can the configuration file just get up and leave". I then did what it asked and tried to reformatted again but worse was upon me. When I put the disk it and ran it it went through its normal motions and I got to as far as when you have to press the F8 key to accept. When I did this it went to the bluescreen of death saying I had a BAD_POOL_CALLER with the numbers 0x000000C2 (0x0000043, 0xC1EA9000, 0X00000000, 0X00000000. This is where I'm currently stuck if anyone out there can tell me how to recover my Raptor Drive to work or completely wipe everything out of it I will the the happiest person ever. Thank you.
Update*
I have currently installed my OS on my normal 500GB harddrive
raptor drive still needs help.
